skip to main content

Push-in connectors

Push-in connectors from AIGO-TEC are the connecting element between a plastic (polyamide or PA) or copper tube and diverse pneumatic systems. They are used for example in pneumatic suspension systems for passenger cars and solenoid switch blocks.

A push-in connector is screwed onto the component using a wrench with a width across flats of 10 or 12. It is important not to exceed the specified torque. Afterwards, one can simply insert the plastic tube into the connector. Connection of the PA tube requires no tools and very little effort. If the PA tube is already mounted prior to screwing on the connector, this is likewise no problem, since the PA tube can turn within the push-in connector. This prevents the pipe from twisting in the connector during mounting and dismounting.

AIGO-TEC push-in connectors are designed for user-friendly installation. The tube can be connected manually, and the connector can be reused.

Material
Brass, aluminium.

Note: Push-in connectors can be reused. In that case, the tube must first be disconnected. Then the push-in connectors can be unscrewed, after which the remainder of the tube can be pulled down and out of the connector.

Our range of push-in connectors

Steckverbinder

Push-in connector NG 4

SV4 MS-G1/8-SW13-17-

Item number: 930635

Length seal screw: 24 ± 1

Thread: G1/8"

Version: Straigth

Residual pressure: 13

Diameter plastic plug: 4 mm

Steckverbinder

Push-in connector NG 6

SV6 MS-M8X1-19

Item numver: 930639

Length seal screw27,7 ± 1

Thread: M8x1

Version: Straigth

Residual pressure12

Diameter plastic plug: 6 mm

Steckverbinder

Push-in connector NG 4

SV4 MS-G1/8-90°-NI

Item number: 930645

Length seal screw30±1

Thread: G1/8"

Version: 90°

Residual pressure-

Diameter plastic plug: 4 mm

Steckverbinder

Push-in connector NG 4

SV4 MS-M10X1-90°-NI

Item numver: 930650

Length seal screw30±1

Thread: M10x1

Version: 90°

Residual pressure-

Diameter plastic plug: 4 mm

Steckverbinder

Push-in connector NG 6

SV6 MS-G1/8-SW13-16-

Item number: 930651

Length seal screw23±1

Thread: G1/8"

Version: Straigth

Residual pressure: 13

Plug connector connection: 6 mm

Push-in connector NG 6

SV6 MS-G1/8-90°-NI

Item number: 930655

Length seal screw35,6±1

Thread: G1/8"

Version: 90°

Residual pressure: -

Diameter plastic plug: 6 mm

Steckverbinder

Push-in connector NG 6

SV6 MS-M10X1-SW12-15

Item number: 930670

Length seal screw24 +1/-3

Thread: M10x1 

Version: Straight

Residual pressure: 12

Diameter plastic plug: 6 mm

Advantages of AIGO-TEC push-in connectors

  • Fast, easy and reliable connection of plastic pipes and tubes
  • Connector can be reused after disconnecting the tube
  • Numerous versions (material, connecting thread, tube diameter)
  • PA tube can turn within the connector
  • Requires little installation space (screw-in depth of only 6 mm, projecting length after mounting between 8.6 and 10.2 mm, max. diameter: 13 mm)
  • The flow rate is defined only by the cross section of the tube; the connector has no adjusting function
  • Repeat installation of the system is possible

Possible uses for push-in connectors

  • Pneumatic systems such as pneumatic suspension and brakes
  • Fuel or lubrication system, possible after adaptation (seal element)
  • Components such as compressors, valve blocks, safety valves, filters and driers
  • Use in diverse pneumatic systems

 

Key Facts

  • Temperature range -40°C to 100°C
  • Standard pressure: 15 bar
  • Area of application: up to 30 bar dynamic
  • Bursting pressure: > 44 bar
    • Width across flats (A/F): NG6 = A/F 12 and NG4 = A/F 10

Are you interested in our push-in connectors?
We will be glad to assist you!

Inquire now